Welch-allyn SureTemp PlusModule - User Manual Manuale Utente Pagina 72
- Pagina / 85
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Saving Ambient Bias SureTemp Plus Module OEM Implementation
72 Confidential Welch Allyn OEM Technologies
45 Probe,
Module,
Patient
Measurement below allowable
temperature values and far below the
low ambient or patient limits.
Patient or environmental temperature
conditions may be too low. Verify
conditions at 80°F and 50°F
respectively. If conditions are valid and
problem persists, replace probe. If
problem still persists replace module.
46 Probe,
Module,
Patient
Measurement above allowable
temperature values and way beyond the
high ambient and/or patient limits.
Patient or environmental temperature
conditions may be too high. Verify
conditions at 110°F and 104°F
respectively. If conditions are valid and
problem persists, replace probe. If
problem still persists replace module.
47 Module Internal calibration resistor (RCAL) on
the board is damaged.
If problem persists, replace module.
48 Module Internal calibration resistor (RCAL) on
the board is damaged.
If problem persists, replace module.
49 Module Internal circuit validation resistor (PTB)
on the board is damaged.
If problem persists, replace module.
50 Module Internal circuit validation resistor (PTB)
on the board is damaged.
If problem persists, replace module.
51 Module A/D measurement timed out and did not
finish in the allotted time slot.
If problem persists, replace module.
52 Probe Probe not characterized/calibrated. Replace probe.
59 Battery/
Voltage
Battery or power-supply voltage below
algorithm maximum value.
Verify that the supply voltage is within
specification.
60 Battery/
Voltage
Battery or power supply voltage
exceeds algorithm minimum value
Verify that the supply voltage is within
specification.
61 Module Reference voltage circuit detected to be
under voltage or unstable.
If problem persists, replace module.
63 Module Probe well missing or not installed
properly
Re-insert probe well or check for
alignment problem.
65 Module Problem saving to the module's
EEPROM.
Verify that the supply voltage is
correct. Try to make changes again. If
problem persists, replace module.
66 Module The module's or the probe's error
detection mechanism detected an error.
Verify that the supply voltage is
correct. Try again. If problem persists
replace indicated component.
67 Module Problem reading the module's EEPROM
or saving to the module's EEPROM.
Verify that the supply voltage is
correct. Try to make changes again. If
problem persists, replace module.
68 Module Problem reading the module's EEPROM
or saving to the module's EEPROM.
Verify that the supply voltage is
correct. Try to make changes again. If
problem persists, replace module.
69 Module Problem reading the module's EEPROM
or saving to the module's EEPROM.
Verify that the supply voltage is
correct. Try to make changes again. If
problem persists, replace module.
Error Class Possible Cause Action
- Welch Allyn 1
- SureTemp 1
- Contents 3
- 1 - Product Overview 7
- Safety and Warnings 8
- Measuring Principle 9
- 2 - Functional Description 10
- Probe Well 11
- Cycle Initiation Switch 12
- Probe Well Switch 12
- 3 - OEM Implementation 13
- Levels follow Vcc and ground 15
- Asynchronous Operation 16
- Figure 4. Thermometry Module 18
- Time-out 19
- Guidelines 20
- Adult Axillary Mode 21
- Pediatric Axillary Mode 21
- Rectal Mode 21
- Monitor Mode 22
- Ready Audible Signal 23
- In-Progress Indicator 23
- Completion Audible Signal 23
- 4 - Specifications 24
- 5 - Verification Testing 26
- 6 - Regulatory 27
- 7 - Part Numbers 29
- 8 - Communications Protocol 30
- Packet Structure 31
- Command Block 32
- Response Block 32
- Type Codes 32
- Data Types 32
- Simple Data Types 33
- TEMP_STATUS 34
- TEMP (33 data bytes) 35
- TEMP (19 data bytes) 36
- Checksum Calculation 37
- Commands and Responses 38
- Command Code (hex) 39
- Response Data 39
- (2A06) Save Data to EEPROM 41
- (2A12) Set Temperature Method 42
- (3000) Restart Module 44
- (3109) Erase Event Log 46
- (3503) Lock Thermometer Probe 46
- (3604) Set Temperature Probe 47
- (9416) Send 690 Event Log 49
- Data Records 54
- Endianness 55
- String Examples 57
- 9 - Quick Start 67
- Introduction 69
- Calculating the Bias 70
- Saving Ambient Bias 70
- 11 - Error Codes and Recovery 71
- Appendix A - Developer’s Kit 75
- Software Installation 76
- Hardware Installation 76
- SureTemp Plus PC Display 78
- Normal Mode 79
- Extended Views 80
- Predict Log 81
- Communications Log 81
- Miscellaneous Functions 82
- Comms Log Window 83
- Full Display 83
- Appendix B - Cleaning 85
Prodotti e manuali riguardandi Apparecchiature Welch-allyn SureTemp PlusModule - User Manual
Apparecchiature Welch-allyn DuraShock Integrated Aneroid Sphygmomanometer - Us Manuale Utente
(8 pagine)
(8 pagine)
Apparecchiature Welch-allyn Allegiance Brand Tactics Blood Pressure Cuffs - Us Manuale Utente
(1 pagine)
(1 pagine)
Apparecchiature Welch-allyn DuraShock Aneroid Sphygmomanometer with Integrated Manuale Utente
(2 pagine)
(2 pagine)
Apparecchiature Welch-allyn DuraShock Integrated Aneroid Sphygmomanometer - Us Manuale Utente
(2 pagine)
(2 pagine)
Apparecchiature Welch-allyn CardioPerfect PRO Link Cable insert - User Manual Manuale Utente
(1 pagine)
(1 pagine)
Apparecchiature Welch-allyn Connex VM data management system - User Manual Manuale Utente
(36 pagine)
(36 pagine)
Apparecchiature Welch-allyn Proxenon Headlight And Fiber Optic Cable - User Ma Manuale Utente
(28 pagine)
(28 pagine)
Apparecchiature Welch-allyn 23820 Otoscope/Throat Illuminator - User Manual Manuale Utente
(4 pagine)
(4 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale